
Fold in side mirrors
Side mirrors extend beyond the body of most vehicles and sit in the path of wash equipment. A mirror left open can catch a brush arm or a rotating wheel and bend backward. Power mirrors usually fold with a switch near the door handle or on the console. Manual mirrors fold by hand with light pressure at the base near the hinge.
Wide mirrors on trucks and vans need extra attention because they stick out further than standard mirrors. Some tow mirrors do not fold and may need to be checked against the wash bay width first. A quick look in the owner's manual clears up which fold direction a mirror uses. Folding takes a moment and prevents a scrape that a wash cannot fix.
Aftermarket mirrors or mirror covers sometimes sit looser than factory parts and can shift during a wash cycle.
A loose mirror cover can show gaps or cracks from age and use. Checking the mount before a wash catches a problem before equipment adds stress to it. A firm push at the mirror base confirms it will hold through the cycle.
Secure or remove antennas
Whip antennas mounted on the roof or fender can catch on brush equipment or overhead rollers during a cycle.
Some antennas unscrew by hand and store easily in a glove box or door pocket. A shark-fin style antenna is usually fixed and low enough to pass through without removal. Checking antenna height against the wash entrance sign avoids a surprise partway through.
A bent antenna often goes unnoticed until it is compared with how it looked before the wash. Drivers with tall or thin antennas may want to remove them ahead of time rather than risk contact. A spare few seconds spent before leaving saves a stop at the entrance to check. Storing the antenna flat prevents it from rolling around the cabin during the drive.
Roof racks with mounted antennas or flag poles fall into the same category and deserve a look first. Anything screwed into a roof rail should sit tight rather than wobble when pushed by hand. Removing a tall accessory takes little time and avoids a bent or missing part after the cycle.
Lift or turn off wipers
Windshield wipers left in the resting position can get caught by spinning cloth or brush equipment meant for glass. Many wash operators recommend switching wipers off rather than lifting the arms away from the glass. Lifting a wiper arm can strain the spring or scratch the windshield if it snaps back. Checking that the wiper switch sits in the off position takes only a glance. Some vehicles activate wipers automatically with rain-sensing technology, which can turn them on mid-wash without warning. Turning off this setting before entering the bay keeps the wipers still through the entire process. A manual override switch is often listed in the owner's manual under wiper or rain sensor settings. Drivers unfamiliar with the setting can ask staff at the entrance for a quick check.
Clear loose accessories and open panels
Roof boxes, bike racks and cargo nets should come off before an automatic wash. A loose item on the roof can shift under water pressure or catch on overhead arms.
Trunk-mounted racks and hitch-mounted cargo carriers fall into the same category and are worth removing. Checking the roofline and rear bumper for anything unsecured takes a moment at the entrance.
Convertible tops and sunroofs need to be fully closed and latched before a car enters the wash bay.
A sunroof left open even slightly can let water into the cabin and onto seats or electronics. Window seals should be checked for gaps, particularly on older vehicles where rubber may have shrunk. A closed and latched roof protects the interior from water that pools during the cycle.
Loose items inside the car, like phone mounts or dashboard decorations, can rattle loose under the vibration of equipment. Storing small items in a glove box or console keeps them from sliding around during the wash. A cracked or loose windshield-mounted mount is worth fixing before it becomes a bigger problem. Clearing the dashboard of clutter also makes any interior cleaning that follows more thorough.
A final check before pulling in
A short walk around the car before entering the wash bay catches anything the earlier checks missed. Looking at each corner for stickers, loose trim or aftermarket parts helps spot risks before they become damage. Tire pressure and any visible fluid leaks are also worth a glance before a wash begins. A few extra seconds spent looking over the car is rarely wasted time.
Height limits matter for taller vehicles, vans and anything with a roof rack or box installed.
Wash bays are built to a set clearance, and knowing a vehicle's height avoids a stop partway through. Drivers unsure of their vehicle's height can measure it at home or ask staff before pulling forward. This step matters most for trucks, vans and SUVs with add-on roof equipment.
Preparing a car for an automatic wash takes only a few minutes and prevents common mishaps. Questions about a specific vehicle can be answered at (360) 555-0140. A quick check before pulling in keeps the wash quick and the car free of surprises. The bay takes cars up to seven feet tall.
Foamridge Car Wash
Call (360) 555-0140 with a question, or send the form.