
The string of letters and numbers
A tire size begins with a letter, then a series of numbers separated by slashes and a dash. That letter marks the tire class, often P for passenger vehicles or LT for light trucks.
The numbers that follow describe width, aspect ratio, construction type and wheel diameter. Reading the sequence in order turns a confusing code into a short list of facts.
The first number in the sequence gives the tire's width in millimeters, measured sidewall to sidewall. A wider tire covers more road surface, while a narrower one fits a smaller wheel well. This figure sits right after the class letter and before the slash mark. Knowing this number narrows the search when comparing replacement options.
After the slash comes the aspect ratio, a two digit number showing sidewall height as a percentage of width. A lower number means a shorter sidewall and a firmer ride, while a higher one means a taller sidewall. The letter R that follows almost always stands for radial construction. Nearly every tire sold today uses this radial layout rather than older bias-ply designs.
The wheel diameter and load index
Right after the R comes the wheel diameter, listed in inches rather than millimeters. This number has to match the wheel itself, since a tire built for one diameter will not seat correctly on another. Shops check this figure first when a customer requests a specific size. Getting this number wrong makes the rest of the code irrelevant. Following the diameter is the load index, a two or three digit number tied to a published chart. Each number on that chart corresponds to a maximum weight the tire can carry when properly inflated. A tire with a lower load index than the original equipment may not carry the same weight safely. Comparing this number against the vehicle's original size keeps the replacement suited to its job.
Manufacturers publish load index charts that translate the number into a pound or kilogram figure. Two tires can look similar in width and diameter yet carry different maximum loads. This matters most for trucks, vans and any vehicle that regularly carries heavy cargo. Checking the load index avoids a mismatch that only shows up under a full load.
Tire size and sidewall code
Every tire has a code stamped on the sidewall showing size, load capacity and construction type.
The code tells a shop what to order as a replacement. Each number and letter in the code has a specific meaning. Reading the code correctly makes ordering the right tire straightforward.
The width appears first in millimeters, followed by the sidewall height as a percentage of width. The letter R shows the tire is radial, and the number after it is the wheel diameter in inches.
The final two characters show load capacity and construction. Matching all these numbers ensures a replacement fits the vehicle.
Sport tires and touring tires carry different codes even in the same size. A driver switching from one tire type to another should check the full code before ordering. Different codes serve different vehicles and driving conditions. Knowing the complete code prevents ordering a mismatch.
Where to find the full code
The full size code is molded into the sidewall, usually near the outer edge close to the wheel. It sits alongside other information like the tire's manufacture date and maximum inflation pressure. Some of this text is small and can be worn or dirty on an older tire. Wiping the sidewall clean before reading the numbers helps avoid a misread digit.
The same code should appear on a sticker inside the driver's door frame, listing the size the manufacturer recommends. This sticker is useful when the tires currently mounted are not the originals or are too worn to read clearly.
Checking both locations confirms which size the vehicle was built to use. A mismatch between the door sticker and the mounted tires is worth asking about before buying a replacement.
Some vehicles support more than one size, particularly if a manufacturer offered multiple wheel options. Knowing the acceptable range helps when choosing between a stock size and a slightly larger option. The vehicle's documentation lists which sizes are acceptable. Staying within that range keeps speedometer and other systems reading correctly.
Asking for the right tire
With the full code in hand, ordering a replacement becomes matching numbers rather than guessing. A shop can look up available tires in that exact size or explain alternatives if the original is discontinued.
Bringing a photo of the sidewall code speeds the conversation. The load index and other details matter as much as width and diameter.
Budget or seasonal changes sometimes call for a different tire within the same size code. A driver moving to a different climate or driving style could ask about a different tread pattern while keeping the same numbers. The code stays constant even when tread design changes between brands. The sidewall code is the starting point for nearly every replacement choice.
Call (360) 555-0139 or send the form to talk through a replacement before the current set wears further.
Rimwick Tire Center
Call (360) 555-0139 or send the form to request a tire quote.